hello guys today i give it, we are here for us it will be the class and today we will learn our first rule in carpentry when we need to hit an iron tool we use another tool also made of iron so when there is a need to hit something wooden we will use a tool that is also made of wood ie iron is hit with iron and wood is hit with wood let the examples a chisel to boot floors or tiles for example hit her like an iron hammer on an iron cable we will fight with a iron hammer as well and in the case of a chisel it even points the iron seal the place where we are going to hit the handle is made of wood so we will also need a wooden tool to hit the handle form a seat or as some like to call hammer of wood or even a straight wooden seat, in addition to being used to knock down in the formal, also used for installing pegs when we are going to join parts of the furniture that is being manufactured as well as to separate parts of wood or real estate without damaging the wood and of course it mainly serves for carving and a wide range of uses that you will learn later in the course this is what I use for many years use continue helping enough but today we will learn to do is to make a brand new now that you've understood how and what will be today's class enough talking and let's err wood is good to start I got four leftover rafter even one of them is even with paint to make our mallet we will need some leftover cairu and a piece of broomstick a seat that I have in the part I used to hit is 12 centimeters wide by 7 centimeters high and 36 centimeters long.
Cable already including the part that will stay inside the hole, I'll opt for the wider piece of rafter and if it's eight centimeters tall it's perfect, I'll do the following di on the other side a seat that is 12 centimeters wide by seven tall, I'll leave this one eight tall by three wide, that is, a little bigger scratch with 13 centimeters from the tip into the position always make two lines on each side to have sure it's correct, now let's connect the risks with the aid of the square, always keeping the frame door on the edge of the cairo and risking on the top, ensuring that our risk is 90 degrees, I'll change places because here it's starting to stay with the neighbor and the quality is getting bad ready here on the outside table is much better for us to record today it's clearer let's mark one centimeter from the top of cairo down to both sides now do the same thing on the other side mark five centimeters from the tip inwards at the top and the other side also turn the coir and mark the same two centimeters on each side of the ends inwards at the top now that you've made the scratches with five centimeters and the two centimeters from the top edge to the inside of the cairo draw a diagonal line from here to here and on the other side the same thing on the top let's scratch an x starting from the ends this x can be done with the pen also or with the pencil where the che is right in the middle in the center mark 1-1 let's repeat the same procedure now on the other side of the car now let's fix this piece of rafter in our display to cut it we can cut it with the saw with a saw bow or even with the circular scene I will cut with the saw if I get too tired to finish and in the saw bow remember we will also need to cut those two diagonal tops or if you prefer and have practice they can also be removed with formaldehyde to advance I cut mine with a saw bow fasten your dating screw from the show here so that it doesn't get on top of the screw and fix the piece well now let's hit the nail right in the middle of the x to mark it no need get the pr The whole ego is just to make a mark on the wood I will use a flat drill for wood and 3 4 inch this change is a little smaller than the broom handle and if we use the one inch the hole will be much wider than the handle there are two ways to make this hole in the first turn more or less to the middle now it becomes a piece and in that other x on the other side of the sea that complete in the center start another hole now on that side until the hole meets the one you made previously, the second option is that you can also drill the right end, making the piece with the drill without the need to turn it, look how the hole was now let's hold it in the girl and it will pass a rasp on the correct side to remove this old paint and this dusty layer that has formed on the surface of the wood now let's hold the piece aside at our death and let's pass the round gloss inside the hole to hit any shape that has been left or flaw left by the drug but go slowly and if Always testing with the broomstick as it will not be able to freely enter its thick round base into the hole with circular movements, note that the broomstick is even thicker than our hole now I will measure scratch the exact size it should enter and give one potato with the drug at the end of the broom handle.
Vague enough just to hate it inside the hole needs to enter with a certain pressure but not exaggerated the handle of the other mallet is 36 centimeters long but that's your option I 'll mark this new car with 36 and a half centimeters if you want to make it larger or smaller, this will be your option, it is very important that you choose a size that gives you greater comfort when handling it or closed with the saw even when it is ready, now apply white glue from the wood to both sides of the hole like this by turning the piece while passing part also at the end of the handle like the other mallet I'll hit the handle so that it enters the hole if you want you can hit it carefully with the iron hammer ro or even with a piece of rafter the piece presents until the end of the hole if you notice that it is going in too forced stop and remove the cable in front of the gloss a little more cleaning the cable glue before and cash with it on second now I will give one pass of sandpaper number 60 to the wood on the top and handle and let it dry until tomorrow this is our mallet ready after 24 hours the white glue has already dried as you can see it got a little bigger compared to the first mallet that I had now, if you want, you can do it or put putty to darken the finish, it's up to you now you have a tool for notching to hit your wooden pieces without damaging them and to help in the next classes to come, we'll use it a lot mainly to beat the formations and speaking of information in the next class we will learn how to make them and spin them including how to make the cables of our formations so you already know don't miss our next class is the one of m and we will be here to continue with our classes because a lot is still to come and you will learn more and more this beginning with tools although it is a bit boring it is very necessary that you will understand why later on and how much they need you.
helped people, it won't be long before we start our projects and you start putting your hands dirty I say on wood click below the video and subscribe because this helps a lot we have the gift of thanking you a lot until the next hour guys.